U-Boot 2010.06.05 (Apr 14 2011 - 10:54:55)

CPU:   AMCC PowerPC 460EX Rev. B at 1150 MHz (PLB=230 OPB=115 EBC=115)
       No Security/Kasumi support
       Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
       Internal PCI arbiter enabled
       32 kB I-Cache 32 kB D-Cache
Board: Sam460ex, PCIe 4x + SATA-2
I2C:   ready
DRAM:  2 GiB (ECC not enabled, 460 MHz, CL4)
PCI:   Bus Dev VenId DevId Class Int
        00  06  126f  0501  0380  00
PCIE1: link is not up.
Net:   ppc_4xx_eth0
FPGA:  Revision 03 (2010-10-07)
SM502: found
VGA:   NO CARDS




Config: PCIe 4x + SATA-2
USB:   scanning bus for devices... 5 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

SATA device 0:
Model: ST3250620AS Firm: 3.AAC Ser#:             5QF012QN
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
] bdinfo
memstart    = 0x00000000
memsize     = 0x80000000
flashstart  = 0x00000000
flashsize   = 0x00000000
flashoffset = 0x00000000
sramstart   = 0x00000000
sramsize    = 0x00000000
bootflags   = 0xFFFCE448
intfreq     =   1150 MHz
busfreq     =    230 MHz
ethaddr     = 00:50:C2:80:D4:A1
eth1addr    = (not set)
IP addr     = 192.168.1.2
baudrate    = 115200 bps
relocaddr   = 0x0FF6D000
] ?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
boota   - start AmigaOS boot procedure
bootelf - Boot from an ELF image in memory
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootvx  - Boot vxWorks from an ELF image
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
date    - get/set/reset date & time
eeprom  - EEPROM sub-system
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fdt     - flattened device tree utility commands
fpga    - show FPGA firmware revision
go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
loop    - infinite loop on address range
md      - memory display
menu    - Show preferences menu
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mtest   - simple RAM read/write test
mw      - memory write (fill)
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
sata    - SATA sub-system
saveenv - save environment variables to persistent storage
setenv  - set environment variables
shutdown- switch machine off
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version